Have you lifted your Jeep and now have drive shaft vibration problems? Install this Slip Yoke Eliminator kit and reduce or eliminate that annoying noise and vibration. Transfer case tailshaft length is reduced by 6.5 on '97-'03 Wranglers and 4.25 on '88-'95 Wranglers reducing the driveline angles. Kit comes with a heavy-duty rear output shaft which is shorter and has 18% larger spline diameter and a 54% increase in torque capacity. New aluminum rear output housing, bearings, seals, snap rings, bolts and instructions. *Some models may require mode fork shift rail to be shortened.
The bell housing was cast incorrectly. Manufacturer does not care last rugged ridge part I will buy. Had to take it back apart after install to ream out housing to make it shift.
The bell housing was cast incorrectly. After little to no support from the manufacturer, I had to fix it. I had to grind away material from the inside of the bell housing to get the transfer case to work properly. Apparently I just got a bad one. I was not pleased that I had to do extra work on a brand new part. I'm just glad I checked it out before re-installing in the vehicle.
i had some trouble with the hardware and i contacted them for customer service. and they treated me exactly the way i expected them to. i love their kit.
i have 1.5 inch rubicon express springs pn my yj will this sye work for that size lift
Asked by nacy newbie from on
Hi Nacy, This Rugged Ridge NP 231 Slip Yoke Eliminator Kit works great on the YJ Wranglers but its usually needed on kits 4" or higher. You'll also need the CV style driveshaft for it, here's the link and thanks for the inquiry. http://www.4wd.com/Drivetrain-Differential/CV-Style-Drive-Shaft.aspx?t_c=12&t_s=515&t_pt=4925&t_pn=EXP4040
Answered by Jim G Ext 4806 from on
I have a 1995 YJ Sahara. It has a 3.5 inch lift and I am installing 35 inch tires. The transfer case was lowered with spacers as part of the lift kit installation and I would like to move it back up to its original position. Do I need this kit to accomplish that. Anything else I would need? (FYI I am doing some minor body mods and front wheel spacers to accommdate the larger tires.) Thanks.
Asked by AZ-YJ from 86406 on
Hi Az-YJ the Rugged Ridge NP231 Slip Yoke Eliminator Kit will put it back at the stock hight but you will need to install this then measure for a drive shaft and order a custom drive shaft for the jeep. If you have any other questions feel free to ask. Thanks,
Answered by roy p ext 4928 from 86406 on
Are there any SYE kits for the TJ NP231 that have 1330 yokes instead of the 1310? I have a cv driveshaft but its set up for 1330 u joints
Asked by Josh from Denver on
Hello Josh, With these slip yoke eliminators you will have to use the 1310 joint, we do not have a setup with the 1330. If you have anymore questions feel free to ask, Thank you.
Answered by [email protected] from Denver on
Rugged Ridge was established in 2005 by the company Omix-ADA to focus on innovative aftermarket Jeep accessories. Many of Rugged Ridge's recent designs are so innovative they have been patented. This includes their floor liners, snorkel and XHD Modular Bumpers. Since 2005 Rugged Ridge has developed and manufactured over 3,000 kinds of Jeep related products. All Rugged Ridge Jeep accessories are trail rated. The Omix-ADA founder came from a family that owned a small Jeep dealership. It was the founder's dream from a young age to own a company that made accessories for Jeeps. The founder manifested the dream in 1992. Shop Rugged Ridge Now