FREE SHIPPING on Orders over $50*
MENU
SEARCH
CALL US
CART 0
    5. Rugged Ridge Body Armor Corner Guards

    Rugged Ridge Body Armor Corner Guards

    Rugged Ridge
    Rugged Ridge Body Armor Corner Guards
    ##Sku-section1 ends2# 18:03:392##

    Features

    • Rugged Ridge's Body Armor Jeep Corner Guards provides paint protection for your Jeep while up-dating the look of your Jeep
    • Each rear corner piece is constructed from impact resistant polycarbonate and custom fit while still leaving room for your license plate
    • Rugged Ridge's rear corners attach with ultra strong 3M automotive grade tape ensure a secure fit with no drilling required
    • Available in Matte Black, or can be painted to match vehicle
    • California Residents: WARNING

    PRODUCT OVERVIEW

    Protecting the rear corners of your Jeep just got a whole lot easier! Each Body Armor piece is constructed from impact resistant polycarbonate and have a stylish matte black finish for the coolest, toughest looking up-grade for your Jeep. The Rugged Ridge Body Armor Corner Guards offers weather resistant protection for the the rear of your Jeep. Attach them to your Jeep with ultra strong 3M tape for a secure fit while adding a touch of style at the same time.

    Reviews

    3.4
    3.4 112
    5 Reviews
    Write a Review
    5.0
    Must have!!

    Well engineered fit, installs in 30mins. Hold up against tree encounters amazingly.


    from OH |
    4.0
    Good item

    Great product and looks good but the holes did not line up at all which made it very difficult to install


    from Hildebran,nc |
    2.0
    Bring a drill and a sharp knife!

    Be ready to loosen the fenders. On the passenger side I couldn't get to the plug for the lite,I think removal of all the plastic parts has to be done, and ended up cutting a slit to get around the wires. On neither side did the mounting holes line up. Either on the gas cap or the lites or the license plate. Make sure you put plugs in the plate mounting holes before installing. Instructions leave a lot to be desired.


    from Coeur d"Alen, Idaho |
    2.0
    NO DRILL! Sort of.

    Supposed to be no drill. Everything included. NOT. Started on left side. Remove lite and licence plate mount. Tried to line up holes, not even close. Line up the gas inlet ok and the tail lite and licence plate holes don't match. Line up the licence plate holes and the tail lite and gas cap holes don't match. OH! and don't forget to mount your plate before attatching the corner. Also you will need to loosen the fender flares, or cut the corner guards. Have a drill and a dremel handy. The hole for the lite plug may need to be enlarged. Needed to drill new holes in the guard to get the screws through. Took me 3 hrs to do the left side.


    from Coeur D Alene, Idaho |
    4.0
    Rear Armor Clad Corners by Rugged Ridge

    It's a great looking product.However;on the install I was expecting the left(Driver)side to be the most difficult;I could'nt have been more wrong. On the other side is where I had the most problems due to the GREAT people at Chrysler. The simple fact that they were'nt very generous with the pigtail wiring that causes you to have to remove the right inner wheel well and traverse the evap. canister to access the connector.Other than that it was pretty simple.


    from Saint Helens Oregon |
    See all reviews

    Question & Answers

    5 Answered questions

    2008 Rubicon Is the license plate holder part of the product or do I re-use the original one? Also, your other corner guard (11651.07) is a little more expensive. Does that mean it is sturdier? Can I screw these in if I wish? The installation instructions would not download.

    Asked by Rick from on

    Rick, the Rugged Ridge Body Armor Corner Guards would be the corners only. The license plate bracket would be reused. The corner guard 11651.07- is a different finish, which is why there is a difference in price. I hope this helps!

    Answered by Sara H. Ext 4874 from on

    Do these guards come as a pair or single?

    Asked by Aussie from on

    Aussie, The Rugged Ridge Body Armor Corner Guards come as a pair. Please let us know if you have any other questions. Thanks!

    Answered by Tom S. Ext. 4876 from on

    WILL THIS WORK IN A 2008 4-DOOR RUBICON?

    Asked by IVAN from TRUJILLO ALTO,PUERO RICO on

    Ivan, No these will only work for the 2-door JK. The ones made by Rugged Ridge for your Jeep are RUG11651.01 I hope this helps!

    Answered by JamieEXT:4917 from TRUJILLO ALTO,PUERO RICO on

    See all questions & answers

    Manufacturer

    Rugged Ridge was established in 2005 by the company Omix-ADA to focus on innovative aftermarket Jeep accessories. Many of Rugged Ridge's recent designs are so innovative they have been patented. This includes their floor liners, snorkel and XHD Modular Bumpers. Since 2005 Rugged Ridge has developed and manufactured over 3,000 kinds of Jeep related products. All Rugged Ridge Jeep accessories are trail rated. The Omix-ADA founder came from a family that owned a small Jeep dealership. It was the founder's dream from a young age to own a company that made accessories for Jeeps. The founder manifested the dream in 1992. Shop Rugged Ridge Now