"Poison Spyders JK Body Mounted Tire Carrier works with the stock rear bumper or just about any aftermarket rear bumper, and can accommodate up to a 40" spare tire and accessories. The main tire carrier assembly is made of 1-1/2" DOM tubing for strength and great looks. All of the plate steel components are CNC laser cut and brake-formed from 1/8" or 3/16" steel plate. The hinge and latch assemblies are designed to address common issues inherent in similar tire carriers from other manufacturers. The tire carrier comes with mounting points to add several Rot-Pax fluid packs as well as a Hi-Lift jack. Poison Spyder Customs BFH front bumper is designed for those hardcore four-wheelers who value strength, simplicity and function. This bumper was literally "Built For the Hammers" with the best ground clearance, tire clearance and approach angle possible. It is no wider than the Jeeps frame rails, with angled facets to improve its ability to slide over the rocks. The BFH bumper is CNC laser-cut from a single piece of high strength 3/16" plate steel, then precision brake-formed for an exact fit. The BFH bumper features an integrated winch mount and one-piece design. The Brawler Bar is a lower-profile Stinger, fashioned after the 2-bend Stinger featured on our Original RockBrawler bumper for JK. The Brawler Bar features the most versatile combination of trail protection and a lower profile for easier access to the engine compartment, fitment into garages and trailers, etc. Plus it looks great! The Brawler Bar extends 7.4" forward from the front edge of the bumper, and 9.8" high from the top surface of the bumper. The Recovery Shackle Tabs are machined from 1" thick plate steel to provide a secure attachment point for 3/4" recovery shackles. These tabs are specifically engineered to match the angles of the BFH bumper to result in zero loss in approach angle. The most vulnerable areas on the body of the Jeep JK are the rocker panels. Poison Spyder Rocker Knockers protect your JKs rocker panel area while enabling you to slide over rocks and obstacles. Rocker Knockers enhance your Jeeps trail performance while adding rugged off-road looks to your JK. Poison Spyder JK Rocker Knockers are engineered for brute strength and impact resistance by attaching to the Jeeps body in 14 strategic bolt locations. The mounting plate is CNC laser cut from 3/16" plate steel and precision brake-formed for a perfect fit. The tubular rocker rail is rugged 1.75" X .120 wall DOM structural tubing. The slider rail is fabricated from CNC-bent 1.5" X .120 wall DOM tubing. The space between the Slider and the main tube of the Rocker Knocker is filled with a CNC laser-cut Slider Skid. The Skid features Poison Spyders exclusive oval dimples for structural strength as well as great Poison Spyder looks. The Skid attaches with countersunk stainless steel flat head cap screws for a flush surface. The Slider and Skid mount at an angle to the main tube of the Rocker Knocker to provide boatside-like protection from the rocks while keeping the Jeeps doors and body a safe distance from higher level trail hazards. Another quality element of the Poison Spyder Rocker Knocker is the ability to remove the outer slider skid. The outer skid is built from 1/8" steel and is secured to a 3/16" base plate welded into the slider hoop assembly. The Slider does not rely on the skid for structure. The advantage of having the ability to remove the skid, is to allow you to replace it if it becomes damaged to a level that it has lost its aesthetic appearance or functionality. Also you will be able to customize the Sliders to match your Jeep, and to easily be able to remove it for re-finish. Poison Spyder JK Rocker Knockers are compatible with all known suspensions and body lifts, including long arm kits. Because the Rocker Knockers mount directly to the Jeeps body tub, they will lift with the body when a body lift is installed (competitors frame-mounted rocker guards may leave a gap on body-lifted vehicles). As an added attribute the Rocker Knocker mounting plate is designed with drain reliefs to discourage debris from collecting in the lower body cavity. Poison Spyder JK Rocker Knockers can be utilized as a stand alone component or can be used in conjunction with Poison Spyders JK Body Armor. JK Body Armor is a secondary line of defense against off road damage to your Jeep, protecting the Jeep by reaching above the Slider level up to the door line. Rocker Knockers do not mount or use the Body Armor for additional structure."
Manufacturing products exclusively for Jeeps, Genuine Packages carries front bumpers, suspension systems, LED light bars, receiver hitches and more. Upgrade your Jeep's bumpers with front and rear ones from Genuine Packages that are compatible with 2 and 4-door models. When you're looking for part replacements to get trail-ready for anything you encounter, products from Genuine Packages fit the bill. We carry a full lineup of interior and exterior items. Forget overpriced parts and accessories for Jeeps and go with products produced by Genuine Packages. Shop Genuine Packages Now
We Pay Your Sales Tax