With over a decade of experience, Trail-Gear has been developing, designing and distributing products for adventurous off-roaders and especially wheelers into rockcrawling. Located in Fresno, California, the company specializes in suspension-related parts and accessories including bumpers, armor, axles and drivetrains. The company's employees live and breathe the off-roading lifestyle and Trail-Gear strives to keep their products affordable without cutting corners on design and quality. When you need suspension systems, recovery and towing accessories or lighting solutions, Trail-Gear can outfit you for the trail and beyond.
Trail Gear's Axle Bearing Service Kit includes all parts for servicing left or right rear axle on 1979-1995 Toyota 4x4 Pickups and 4Runners. Kit Includes Koyo axle bearing, axle housing seal, axle bearing retainer, outer axle rubber seal, c-clip, axle o-ring.
Trail-Gear O.D. Tube Clamps are ideal for suspension and steering brackets that you need attached to a section of tubing when you don?t want to weld the bracket directly to the tubing because adjustment or frequent removal of the bracket is needed. The O.D. Tube Clamp is perfect for attaching shock brackets to suspension link or steering brackets to steering rods or links and allows you to attach steel mounting brackets that are readily available to aluminum suspension links and steering rods that you could not otherwise weld steel brackets to. Manufactured from 1020 steel, with a clamping force of up to 8,600lbs these tube clamps will not fail even under the most extreme circumstances. Sold Individually.
Need to place a support tube across your truggy or buggy, but need the flexibility to remove a motor, transmission, or even a seat? We have the perfect solution for you, Trail-Gear?s Interlocking Tube Clamps. They are machined from 100% 4130 Chromoly and use a counter sunk allen head screw.
Trail-Gear introduces the industry's first 6-layer, 1.75 inch nylon webbing limit straps. Each strap features 4130 heat-treated Chromoly Steel buckles that have been zinc-plated for corrosion-resistance and mounting holes. These straps are made from 9,000 lb. test nylon straps and offer minimal stretch to protect against full extension and possible breakage of the shocks on even the most extreme terrain. Anti-abrasion clips have been installed in each buckle to minimize wear. Strap lengths are measured from the center of the mounting holes and are guaranteed accurate to +/-. When selecting, choose a limit strap that is 1 inch shorter than the shock to prevent full extension and possible breakage of shock. Sold individually.
With 30 spline birfields, six stud knuckles, and chromo hub gears or drive flanges, the next weak link in your front axle is your hub studs. When they fail you will be left without four wheel drive, and often times the hub will be unrepairable. Trail-Gear, in partnership with ARP, have designed the most durable hub stud on the market.
The main body of this rod end is 100% 4340 chromoly and then finished with a zinc coating, the ball is made out of AISI 52100 material and then hard chrome-plated for a tough finish. The liner is made out of a teflon. Comes with the jam nut.
If you're installing crossover steering on your 79-85 4wd Toyota you're going to need to mount an IFS steering box. This frame mount kit includes both inner and outer frame reinforcing plates, grade 8 bolts, DOM tubing, and Crimp nuts. Inner plate is 3/16 inch, outer plate is 1/4 inch. Angled leading and trailing edges prevent frame cracking. Heavy duty design.
Prevents dirt, debris and water from getting in to your axle through the stock axle housing breather. Expands and contracts to accommodate increase or decrease in housing pressure. Kit includes one housing fitting, clamp and bellows. Easy installation takes just a few minutes. This product is not compatible with the Trail-Gear rear axle 4 link upper link mount kit.
These shock mounts are designed to weld directly on to the axle housing. Can be used for front or rear axle applications. Made from 3/16 inch plate steel. Mounts have curved bottoms that can be mounted horizontally or vertically on axle. Mount is 2.5 inch tall with 1/2 inch shock mount holes.
High misalignment spacers increase misalignment by continuing the spherical diameter of the ball and allowing the edge of the ball to rotate into the body of the rod end. This allows greater articulation, more suspension travel, and longer life of the rod end.
We are happy to introduce our new GM Style Alternator Bracket Kit. This bracket kit will allow you to bolt a GM style 1 wire alternator to your 20R, 22R or 22RE motor with no major modifications, and it works with your stock alternator belt. This kit will allow you to say goodbye to the small underpowered OEM Toyota alternator and upgrade to a GM style unit that will supply ample power for your rock lights, stereo, GPS and all the other gadgets that are required for modern day rock crawling and racing.
The lens cover is 2.5 inch x 1 inch and is manufactured out of polycarbonate plastic, making the lens much more impact resistant than other lenses made out of the more common acrylic plastic. These 12V LED lights are 100% water proof, sealed with epoxy, and meet SAE Standard J2042-2003.
This steering column will allow you to use your existing Toyota steering linkage without having to buy a coupler and then cut and weld on your steering shaft. This steering column measures 3 1/4 inches from the base of the flange to the outer edge of the shaft, and fits most brands of steering valves (Orbitals) that are commonly used in this application.
The mounting plate is made out of 3/8? thick steel with a 1? thick d-ring mount and 1/2? laser cut hardware. This d-ring mount is designed for their 3/4? d-rings. Available in a 3?x3? and 3?x3.5? mounting patterns.